美國GE公司氧傳感器應用：1.用非危險性的低氧含量氣體（例如：高純氮?dú)猓┐祾呷酉到y(tǒng)。在正常工作時，要求通入傳感器測試頭的氣體為500cc/min（1.0SCFH），壓力為大氣壓。持續通入該氣體，直到完成傳感器的安裝。2.在安裝前，編程和校準的步驟。然后，調整4-20mA模擬輸出，并將測氧的量程范圍設置到0-25%O2。3.打開密封盒，取出氧傳感器。為了保持氧傳感器的能量，立即除去紅色貼片，進行下一步。4.調整傳感器，讓它的金層電極對準變送器的底座上具有彈性的接觸管腳。用手將傳感器緊緊壓在O2X1變送器上。5.此時對新傳感器進行空氣校準。在0-25%的氧量程范圍時，正確的傳感器校準會使變送器4-20mA的模擬輸出端輸出17.4mA的電流。6.用滾花螺母將校準過的傳感器封裝在變送器的測試頭內，調整好變送器的位置，用手?jǐn)Q緊滾花螺母。7.模擬輸出的讀數應該開始下降，平衡時會達到較低的氧含量。此時，重新設置需要的量程范圍。8.為O2X1供電。O2X1經過大約15秒鐘的初始化后，三個LED指示燈會同時短時間地亮起。為了提高PPM傳感器的測量精度，現在可以進行量程氣校準。

氧傳感器OX-1，氧電池OX-1氧傳感器OX-2，氧電池OX-2氧傳感器OX-3，氧電池OX-3氧傳感器OX-4，氧電池OX-4氧傳感器OX-5，氧電池OX-5

Sensors available:

• OX-1: Standard ppm sensor
• OX-2: Acid gas resistant ppm sensor
• OX-3: Standard percent sensor
• OX-4: Acid percent sensor
• OX-5: Standard ppm sensor (minimum measurement of 5 ppm)

Replacement oxygen sensors for Panametrics oxygen transmitters. Sensors available:

• OX-1: Standard ppm sensor, 0 to 10, 20, 50 ppm, minimum measurement is 0.2 ppm
• OX-2: Acid gas resistant sensor for O2, 0 to 10, 20, 50, 100, 200, 500, 1000 ppm, minimum measurement is 0.2 ppm
• OX-3: Standard percent sensor, 0 to 1, 2, 5, 10, 25, 50%, minimum measurement is 0.01 (100ppm), accuracy reduced in the range above 50%
• OX-4: Acid gas resistant sensor for % O2, 0 to 1, 2, 5, 10, 25, 50%, minimum measurement is 0.01 (100ppm), accuracy reduced in the range above 50%
• OX-5: Standard ppm sensor, 0 to 100, 200, 500, 1000, 2000, 5000, 10000 ppm, lower cost version of the OX-1, minimum measurement is 5 ppm.

10,000 ppm = 1%; % sensor recommended for this range, for 2000 and 5000 ppm ranges any sensor can be used

實物展示